If you need to inquire or purchase ,please send the product models to my email or call me directly .

Contact detail:

Xiamen Xiongba E-commerce Co., Ltd

Mobile/ WeChat/ WhatsApp:+86 13365909307

E-mail: dcsplcsales@gmail.com   

Contact:   Simon Zhang

Website: https://www.dcsplcsystem.com

Address: Unit 2008, Chuangxiang Center, No. 1733, Luling Road, Siming District, Xiamen, Fujian


The on-site debugging work mainly involves checking and using the system software, and conducting configuration confirmation and functional testing on the application software.
1. Inspection before power on
The cable insulation resistance meets the requirements (greater than 5M ohms). Check the cable insulation resistance test records and conduct spot checks and measurements if necessary.
Verify that all power lines, signal lines, and communication buses are connected correctly.
The models and positions of the cards, adapters, and their interfaces in the control station, operation console, engineer station, and other frames are correct and correct.
QUICKPANEL QPI-GEG-201-H  
NI SCXI-1125       
GE 369-HI-R-M-0-P-0-E 
GE IC698ETM001
GE IC698CPE030  
GE IC698PSA100  
GE IC698CHS009   

ABB 64691929 DSMB-01C 
HIMA 982200425 F3 DIO 8/8 01  
HIMA 982200416 F35            
HIMA 982200409 F3 AIO 8/4 01  
SCHIELE DL42N-22  


ABB 3BSE042234R2 PP835A  
TRICONEX 3721      
FOXBORO P0904AK          
PARKER 1037302 6K8            
PARKER 1019422 EVM32-BASE  
WOODWARD 8444-1067       
FOXBORO P0916RH FBM219    
GE IS420UCSBH4A  
FOXBORO P0904AK   
EMERSON MVME7100  
SMC INR-244-203B  
Lenze   9215                  
ABB 3HAC028357-001 DSQC679  
EMG ECU01.5         
SCHNEIDER   MM-PM41400C/PM+4000  
ABB 5SGX1060H0003                       
ABB 5SGX1445H0001                        
WESTINGHOUSE 1C31166G02        
SENTRY 7-00744A VREL-11   


The preset knob positions for each card are correct.
The power switch on the power unit and card is in the "OFF" position, and all fuses are intact.
All connecting screws inside the cabinet should be firm and not loose.
Grounding system grounding resistance test:
Remove the "MG" and "CG" grounding busbars from the control room grounding plate, and use a grounding resistance tester to measure the basic grounding resistance separately, which should meet the design requirements (less than 10 ohms).
ABB 1MRB178066R1/E / 1MRB150083R1/E / 1MRB300162R0008 ARND:D 216EA62   
ABB HESG441635R1/HESG216877/K  216NG63A           
ABB HESG324426R0001/HESG324389 REX010     
ENTERASYS SSA-G1018-0652       
ABB AINT-14C 
ABB IEPAS02   
TRICONEX 3721      
GE D20 EME   
Schneider 40-14350-02   
ABB 3BHB003041R0101 UFC719AE01  

Use a multimeter to check if the grounding busbar of each cabinet is connected to the "MG" and "CG" grounding plates.
The insulation resistance between "MG" and "CG" measured should meet the requirements of GBJ93-86 specification (greater than 5M ohms).
UPS power supply test:
Check that both the power panel and the power switch are in the "OFF" position.
The UPS will be put into operation by electrical personnel, and the voltage measured before being sent to the main power switch of the instrument power panel should be 220VAC ± 10% and 50Hz ± 2%.
UPS uninterrupted test shall be conducted by electrical personnel. After fully loaded operation, repeat this test, and the battery power supply time should not be less than 30 minutes
HESG216791/A
UNS2880b-PV2 3BHE014967R0002
UNS2880b-PV2
3BHE014967R0002
UNS0887A-P 3BHE008128R0001
UNS0887A-P
3BHE008128R0001
UNS2882A 3BHE003855R0001
ABB 3BSE042237R1 PP836       
.HONEYWELL FC-SAI-1620M  
SCHNEIDER 140CPS22400  
ICS TRIPLEX T8110B             

A-B 1794-ASB      
ABB 3BSE043660R1 CI867K01  
ABB 0240289352/1100 EL3040      
ABB 3BSE012545R1 CI546        
3BHE009681R0101
GVC750BE101
UNS0881a-PV1 3BHB006338R0001
UNS0881a-PV1
3BHB006338R0001
CI854  3BSE025347R1
CI854
3BSE025347R1
PM783F 3BDH000364R0002
PM783F
3BDH000364R0002
PFTL101BE 2.0KN 3BSE004214R1
PFTL101BE 2.0KN
3BSE004214R1
LXN1604-6 3BHL000986P7000
LXN1604-6
3BHL000986P7000
UFC760BE43   3BHE004573R0043

Perform the following power-on tests on each cabinet and operating console one by one:
Place the cabinet power switch inside the power panel in the "ON" position and use a digital multimeter to check the voltage before the main power switch of the cabinet, which should be 220 ± 22VAC.
Confirm that all cards in the cabinet (excluding power cards) have been unplugged from the card holder, and then place the main power switch, power unit, and power switch on the power card in the cabinet in sequence to "ON". Use a digital voltmeter to measure the DC voltage output, which should meet the manufacturer's instructions (5.1 ± 0.02V, -12 ± 0.3V, 12 ± 0.3V, 24 VDC). If it exceeds the allowable deviation range, make adjustments.
Perform a manual switching test with dual power sources.
Connect the power to each nested fan, signal converter fan, hard drive fan, cabinet top, door fan, etc., and check that each fan is operating normally.
Check if the power alarm circuit is working.
EMERSON 12P6381X032/KJ2005X1-MQ1 VE3008  
EMERSON 12P4375X032/KJ2005X1-BA1 VE3007  
HONEYWELL 8C-PCNT02     
EXTREME SSA-T8028-0652 P0973LN  

MOOG D136-001-007  
GE DS200DCFBG1BNC   
RKC REX-B871*NNCS1B  
BENTLY NEVADA 3500/50  
ABB 58967441E      NTAC-02  
ABB 3BSE008105R1 SC560       
ABB 3BSE012545R1 CI546        
BENDER 107TL47   

REXROTH DKCXX.3-100-7  
SAIA PCD2.M110     
SAIA 463665500  PCD4.D1XX              
NI SCXI-1300      
NI SCXI-1180       
PTVME PT-VME330A  
A-B 1794-ASB/B    
WOODWARD 9907-018  
HONEYWELL TK-FXX102  
A-B SRS50-HFA0-K01  
PACIFIC SC904-001-01  
TRICONEX 4211     
TRICONEX 3805E   
WESTINGHOUSE 1C31222G01   
WESTINGHOUSE 1C31219G01   .
TRICONEX 3721      
TRICONEX 3664      
KOKUSAI  CXP-544A KOMS-A2   
MOOG D136-001-001  
MOOG D138-002-002  （加密狗）
GE VMIVME-5567-100 IC698RMX016    
ABB 3BSE003816R1 PFSA140